All you need to know about coronavirus: www.sacoronavirus.co.za

cleanite-product

CLEANiTe


A ready-to-use solvent for removing dried adhesive residues and cleaning of floor surfaces.

 CLEANiTe® A ready-to-use solvent for removing dried adhesive residues and cleaning of floor surfaces

 

Mixing


is pre-mixed and does not require mixing. It should be used undiluted for optimum results.

General


All data supplied is based on laboratory tests conducted at 20º C, and 50% Relative Humidity. On-site atmospheric conditions may require adaptation to suite circumstances.

Warning


Do not ingest. Keep away from children and pets. Do not empty into a drain. Wear rubber gloves, and in the event of prolonged contamination, rinse thoroughly with cold water. Seek medical attention if irritation persists. Consult our Material Safety Data Sheet for more information.

Important Notice


The information supplied in our literature or given by our employees is given in good faith.
We reserve the right to update this information at any time without prior notice. We guarantee the consistent high quality of our products, however, we have no control over the site conditions or execution of the work. We accept no liability for any loss or damage which may arise as a result thereof.

Warranty


iTe Products® CLEANiTe® is manufactured to comply with the required standards for use as a primer with self levelling screeds in respect of Flow promotion, substrate binding and preventing air bubbles from surfacing during setting.
This warranty is based on the substrate being sound, dry and free of contamination. All application is to be carried out in strict compliance with the application methodology in the data sheet as issued.
iTe Products® further warrants that the products are manufactured to strict quality control standards and that the products supplied are free of defect. We cannot be held responsible for failure due to the substrate failing, or physical or excessive mechanical damage occurring to the applied product.

Application


Ensure that the room is ventilated to prevent build- up of fumes. Pour some CLEANiTe into a clean cloth and place wet cloth over the adhesive to be removed for a few seconds to soften the glue, and then rub to remove it. Most forms of soiling can be removed by this process.

Description


CLEANiTe® is a is a ready-to-use solvent for removing dried adhesive residues and cleaning of floor surfaces with PU and PUR finishes. It contains a non-aggressive turpene based solvent system which enables the removal of old adhesive residues etc from vinyl and similar resilient floor coverings. Provided ventilation is possible, CLEANiTe has a high flash point and does not display explosive properties as with conventional solvent systems such as Toluene etc.

 

Additional Information


Mixing

is pre-mixed and does not require mixing. It should be used undiluted for optimum results.

General

All data supplied is based on laboratory tests conducted at 20º C, and 50% Relative Humidity. On-site atmospheric conditions may require adaptation to suite circumstances.

Warning

Do not ingest. Keep away from children and pets. Do not empty into a drain. Wear rubber gloves, and in the event of prolonged contamination, rinse thoroughly with cold water. Seek medical attention if irritation persists. Consult our Material Safety Data Sheet for more information.

Important Notice

The information supplied in our literature or given by our employees is given in good faith.
We reserve the right to update this information at any time without prior notice. We guarantee the consistent high quality of our products, however, we have no control over the site conditions or execution of the work. We accept no liability for any loss or damage which may arise as a result thereof.

Warranty

iTe Products® CLEANiTe® is manufactured to comply with the required standards for use as a primer with self levelling screeds in respect of Flow promotion, substrate binding and preventing air bubbles from surfacing during setting.
This warranty is based on the substrate being sound, dry and free of contamination. All application is to be carried out in strict compliance with the application methodology in the data sheet as issued.
iTe Products® further warrants that the products are manufactured to strict quality control standards and that the products supplied are free of defect. We cannot be held responsible for failure due to the substrate failing, or physical or excessive mechanical damage occurring to the applied product.

Application

Ensure that the room is ventilated to prevent build- up of fumes. Pour some CLEANiTe into a clean cloth and place wet cloth over the adhesive to be removed for a few seconds to soften the glue, and then rub to remove it. Most forms of soiling can be removed by this process.

Description

CLEANiTe® is a is a ready-to-use solvent for removing dried adhesive residues and cleaning of floor surfaces with PU and PUR finishes. It contains a non-aggressive turpene based solvent system which enables the removal of old adhesive residues etc from vinyl and similar resilient floor coverings. Provided ventilation is possible, CLEANiTe has a high flash point and does not display explosive properties as with conventional solvent systems such as Toluene etc.